Bill William's replication, HHO

[ Pobierz całość w formacie PDF ]
OS:Joe Cell:Replications:Bill Williams - PESWiki
http://peswiki.com/index.php/OS:Joe_Cell:Replications:B...
OS:Joe Cell:Replications:Bill Williams
From PESWiki
Bill Williams' Replication
Joe Cell
Replication
Project
Bill Williams replication in the Joe
Cell Replication Project.
Bill had his truck running on a Joe
Cell, with tremendous power in the
first part of April, 2006. He was
visited on April 11 by two men who
told him to stop all alt energy
activities. He complied, destroying
his lab notes, etc. See story at
JoeCellHydra.com
¤ Hydra Home
¤ Proton Cell
¤ Latest
¤
Submit (http://www.pureenergysystems.com/submit/index1.html)
¤ Cautions
Instructions
¤ Materials
¤ Blueprints
¤ Subtleties
¤ Videos
¤ FAQ
Replications
¤ Validation
¤ Bill Williams
¤ BJ's Proton Cell
Supplemental
¤ Kanarev
¤ Theory
¤ Needs
¤ For Sale
¤ Contacts
Forum
¤
Seminar (http://pureenergysystems.com/academy/JoeCell2006/)
July 30
¤ JoeCell2 (http://groups.yahoo.com/group/JoesCell2/)
¤ JC FE
device (http://groups.yahoo.com/groups/joecellfreeenergydevice)
¤ PESWiki
¤ Supression Reply
1 of 7
8/1/2007 8:28 AM
OS:Joe Cell:Replications:Bill Williams - PESWiki
http://peswiki.com/index.php/OS:Joe_Cell:Replications:B...
-Joe Cells Directory
-Category:Joe Cells
-Wiki tips
PESN.com (http://pesn.com/2006/04/13/9600257_Bill_Williams_threatened/) (Apr. 13, 2006).
The following is pieced together from what others had about Bill's replication.
.
Table of contents
1 Bill's Replication
1.1 Introduction
1.2 Discussion Group Posts
1.3 Video
1.4 Images
1.5 How he did it
2 See also
Bill's Replication
Introduction
Joe Cell Truck Builder Threatened, Destroys
Plans (http://pesn.com/2006/04/13/9600257_Bill_Williams_threatened/) - After
announcing that he had successfully built a truck that runs on Joe Cell technology, drawing
energy from water and Orgone, Bill Williams said he was approached by two men who
requested that he stop his research, threatening him with dire consequences if he didn't.
Others are keeping it alive. (PESN; Apr. 13, 2006)
Running a vehicle on Joe Cell is difficult and
unstable (http://pesn.com/2006/06/22/9500284_Bill_Williams_Joe_cell/) - Bill
Williams has said it took weeks to get his truck to the point of running 100% on the Joe cell,
and that once achieved the system was very unstable and dangerous. Much R&D remains.
(PESN; June 22, 2006)
Discussion Group Posts
Ford Test Drive (http://groups.yahoo.com/group/JoesCell2/message/16) - Bill describes how
his Ford performed with the Joe Cell. "It the throttle response was very crisp or touchy. With
about a 1/8" of movement the next thing I new I was booking at close to 80 mph. If I lifted of
ever so slightly on the throttle and it felt like I was putting the brakes on and the speed would
drop down to 30 mph or so." (Apr 6, 2006)
"Yes" (http://groups.yahoo.com/group/JoesCell2/message/33) - Bill's answer to question:
2 of 7
8/1/2007 8:28 AM
OS:Joe Cell:Replications:Bill Williams - PESWiki
http://peswiki.com/index.php/OS:Joe_Cell:Replications:B...
"have you been threatened by men touting guns". (Apr 11, 2006)
Joe cell lid (http://groups.yahoo.com/group/JoesCell2/message/143) - The reason Bill's engine
was erratic was because the outside air was getting into the engine via breather holes, etc.
fuel pump, distrbutor, and PCV Oil filler cap. also tweaking the timing. -- Peter (Apr 17, 2006)
Video
Video of Bill Williams Ford Engine Running on Joe
Cell (http://www.freeenergynews.com/Directory/JoeCells/replications/Bill_Williams/fordrunningonwater.avi
- 1 minute video. Shows Joe cell inside engine compartment near front of vehicle, connected
via tube to the under-side of the carburetor. (March 20, 2006)
Images
Ronald <rlm555339 {at} netscape.net>, who received regular correspondence from Bill about the
project prior to the crack-down on Bill Williams, sent the following images on April 15, 2006, with
the following preface statements:
"I have 9 photos of Bill Williams cell components in an exploded view which he sent to me
prior to his drama. He sent them to me as a visual aide on how his cell went together since he
and I were corresponding regularly before his incident. These are Bill's photos taken by Bill of
Bill's actual cell he got stomped for. So this is the baby that worked. This was to show me
what the individual components looked like and to show me the welding on the bottom. The
top plate is screwed on. I don't have pics of that but there were some posted somewhere.....I
can't remember where."
The image descriptions were added by Sterling Allan, from a guess. Please correct if needed.
The images are dated March 27, 2006.
Cylinders set out individually, with center rod and end plate laying flat on table.
3 of 7
8/1/2007 8:28 AM
OS:Joe Cell:Replications:Bill Williams - PESWiki
http://peswiki.com/index.php/OS:Joe_Cell:Replications:B...
End plate components laid out separate, prior to assembly. End plate, washers/insulator, nut,
center rod.
Metal center rod with white washer spacers/insulators position illustrated, minus the end plate,
which is laying to the left.
4 of 7
8/1/2007 8:28 AM
OS:Joe Cell:Replications:Bill Williams - PESWiki
http://peswiki.com/index.php/OS:Joe_Cell:Replications:B...
End plate fastened on with nut, with washer spacers/insulators.
End plate fastened to rod.
End plate welded to outer cylinder.
5 of 7
8/1/2007 8:28 AM
[ Pobierz całość w formacie PDF ]

  • zanotowane.pl
  • doc.pisz.pl
  • pdf.pisz.pl
  • braseria.xlx.pl

    •